What Are The Basic Angles Of A Twist Drill?

Aug 08, 2025|

A twist drill is a tool used to drill round holes in workpieces by rotating and cutting along its relatively fixed axis. It is named after its chip flute, which is spiral-shaped and resembles a twist. The spiral flute can have 2, 3, or more flutes, but 2 flutes are the most common. Twist drills can be clamped and used on manual or electric handheld drilling tools, or on drilling machines, milling machines, lathes, and even machining centers. The drill material is generally high-speed tool steel or cemented carbide.
Do you know what are the basic angles of a twist drill? Let's learn about them together!
(1) Helix angle β The helix angle refers to the angle formed between the straightened helix line of the outermost circle on the drill's helical groove and the axis of the drill. Since the lead of each point on the helical groove is the same, the helix angle varies at different diameters of the drill, with the largest helix angle at the outer diameter and the smaller one closer to the center. Increasing the helix angle increases the rake angle, which is beneficial for chip evacuation, but reduces the rigidity of the drill. The helix angle of a standard twist drill ranges from 18° to 38°. For drills with smaller diameters, a smaller helix angle should be adopted to ensure the rigidity of the drill.
(2) Rake angle γOm [Due to the helical surface of the twist drill's rake face, the rake angle at each point on the main cutting edge varies. The rake angle gradually decreases from the outer circumference to the center. The rake angle at the tool tip is approximately 30°, while it is around -30° near the chisel edge. The rake angle on the chisel edge is -50° to -60°.
(3) The clearance angle αOm [the clearance angle at a selected point on the main cutting edge of a twist drill] is represented by the feed clearance angle αOm in the column profile of that point. The column profile is formed by drawing a straight line parallel to the drill axis through a selected point m on the main cutting edge, and then rotating this line around the drill axis to create a cylindrical surface. αOm also varies along the main cutting edge, becoming larger as it approaches the center. The clearance angle α at the outer circumference of the twist drill is usually taken as 8°~10°, while the clearance angle at the chisel edge is taken as 20°~25°. This can compensate for the reduction in the actual working clearance angle at various points on the main cutting edge due to the axial feed motion of the drill, and can adapt to changes in the rake angle.
(4) Main deflection angle κrm. The main deflection angle refers to the angle between the projection of the tangent of the selected point m on the main cutting edge on the base plane and the feed direction. The base plane of a twist drill is the plane that passes through the selected point of the main cutting edge and contains the axis of the drill. Since the main cutting edge of the drill does not pass through the axis, the base planes of various points on the main cutting edge are different, and the main deflection angles of these points are also different. After the point angle is ground, the main deflection angles of various points are also determined. The main deflection angle and the point angle are two different concepts.
(5) Point angle 2φ The point angle refers to the angle formed by the projections of the two main cutting edges on a plane parallel to them. A smaller point angle facilitates cutting into the workpiece, reduces axial resistance, increases the working length of the cutting edge, decreases the nominal thickness of the cutting layer, and is beneficial for heat dissipation and tool durability. However, if the point angle is too small, the drill strength decreases, deformation increases, torque rises, and the drill is prone to breaking. Therefore, the point angle should be ground appropriately according to the strength and hardness of the workpiece material. The standard point angle 2φ for twist drills is 118°
(6) Chisel edge oblique angle ψ The chisel edge oblique angle is the angle between the main cutting edge and the projection of the chisel edge on a plane perpendicular to the drill axis. When the flute of a twist drill is ground, ψ is naturally formed. As can be seen from Figure 3-5, as the chisel edge oblique angle ψ increases, the length of the chisel edge and the axial resistance decrease. The chisel edge oblique angle of a standard twist drill is approximately 50°~55°.

Send Inquiry